HomeProductsZ - shaped belt conveyorsZ-belt conveyor GES-50-ZW

Z-belt conveyor GES-50-ZW

The GES-50-Z-W has a completely closed frame made of a 50 mm high stainless steel profile which meets the highest hygienic standards.

On the driving and deflecting roller, the adjustment mechanics incorporate the CleanTec-System. With it, all moving parts and open threads are sealed inside the conveyor. By this the accumulation of contamination is effectifly reduced. Like the GES-50, the GES- 50-Z-W can also have the patented fast cleaning system with a flip-up roller.

With its 50 mm high frame, the GES-50-Z-W is just the right conveyor for the transport of small loads in pharmaceutical, chemical and food industry.

Compared to the GES-50-K-W, the GES-50-Z-W has another horizontal part on the top end of the conveyor. This is why the conveyor can hand over the transported goods - after covering a difference in altitude - like a flat conveyor.

The GES-50-Z-W is equipped with a white belt that is FDA approved. The height of the corrugated edges and the slats as well as the distance of the slats to each other can be made to suit the application of the conveyor.

The angle of the rising section can be infinitely adjusted between 40 and 60° from the ground. The length of the one rising and both horizontal sections can be made to measurement for specific applications. However, a total length of 4 metres should not be exceeded.

In a standard configuration, the GES-50-Z-W has small casters mounted in A1, that make it very easy to move the conveyor around.

In the rising part an H-shaped support on wheels with brakes, or alternatively double supports made of stainless steel, as shown on the GES-80-Z-W, can be used.

Request quote!
Or call us directly under: +49 (0) 2461 / 93767-0

Technical Specifications and Accessories:

Useable belt widths(between the corrugated edges) / Total belt width:
130/300mm or 230/400mm or 330/500 mm or 430/600 mm

Rising distance between axes, A2: 500 to 3.000 mm. All intermediate lengths possible.
Horizontal distance at the top, A3: 500 to 3.000 mm. All intermediate lengths possible.
Total length A2 + A3:

Horizontal distance at the bottom, A1: 500 to 3.000 mm. All intermediate lengths possible.
Rising distance between axes, A2: 500 to 3.000 mm. All intermediate lengths possible.
Horizontal distance at the top, A3: 500 to 3.000 mm. All intermediate lengths possible.
Total length A1 + A2 + A3: no more than 4.000 mm.

Drive with constant belt speed:
v = approx. 4,0 / 7,3 / 11,0 / 14,7 / 22,0 or 31,4 m/min.
Other belt speeds are possible on request. Connection for 220/240 - 380/415 V, 50 Hz. Protection type IP 65. This drive can be supplied together with a motor protection switch incorporating an emergency off. It has a 2 metre supply cable and CEE plug and is of protection type IP 65.

Drive with infinitely adjustable belt speed:
v = approx. 1,6-5,6 / 2,9-10,3 / 4,4-15,4 / 5,9-20,5 / 8,8-30,8 or 12,6-44,0 m/min.
Other belt speeds are possible on request. The drive is supplied together with a frequency regulator that is ready to be plugged to 240V 50 Hz and has a protection type of IP 65. The frequency controller incorporates a digital motor protection switch.

Geared motor position:
Pulling the belt at its side, on the left or right.

Total belt load:
Standard is of 30 kg. Higher loads are possible on request.